Chipping Thinset Away with a Putty Knife
Pour 0.39 gallons (1.5 L) of boiling water gently over the thinset. Within 40 to 60 minutes of water application, you should notice cracks starting to appear in your thinset. This decreases its integrity and makes it much easier to remove using a putty knife. Purchase 0.39 gallon (1.5 L) cooking pots from home hardware stores. Pots that are 0.39 gallons (1.5 L) in size will cover a region of approximately 107.639 square feet (10.0000 m). Add 1 cup (240 ml) of citrus degreaser or vinegar to your pot to help weaken the thinset.
Hammer your 1 in (2.5 cm) putty knife at a 45-degree angle to the thinset. Firmly hit the end of the knife with the flat end of a 2 lb (0.91 kg) hand maul. Don't hit the knife too hard or you risk breaking the blade and damaging your flooring. After 20 to 30 seconds of hammering, you should notice the thinset breaking apart. If not, pour some more boiling water over it to loosen it. You can also use a masonry chisel that is the same width. Continue removing the thinset in small chunks until you've removed enough to accommodate your new tiles. Always use a putty knife with a hammer-end handle and sharp blade.
Sharpen your putty knife when it gets dull. Hold the knife at a 20-degree angle to a sharpening stone on the left or right side. Align it perpendicular to the stone, and then drag it down its length. Flip the knife over and repeat this motion with the motion side of the blade. Continue this process until your knife is sharp enough to consistently remove thinset. Use a coarse stone for sharpening first. If your knife still needs sharpening afterward, use a fine stone. Apply 1 drop of sharpening or honing oil to the surface of the stone and rub it in with your finger prior to sharpening. These products can be purchased at home hardware stores. Between the 2 stones, the grit range should be 325 (coarse) to 1200 (extra fine).
Remove the remaining thinset with an angle grinder. Attach a 5 to 7 in (13 to 18 cm) diamond cut wheel to an angle grinder with a 4.5 in (11 cm) cup wheel. Connect a 5-horsepower wet-dry vacuum to the grinder by pressing its hose into the hole located in the dust shroud. Move the grinder in up and down motions, working in sections about 2 to 3 ft (0.61 to 0.91 m) long at a time. You can typically remove enough thinset with a chisel to lay tile evenly, but it's very difficult to completely remove all of it. For the smoothest possible surface, finish the job with an angle grinder and a diamond grinding wheel.
Using a Hammer Drill
Attach a 2 to 3 in (5.1 to 7.6 cm) chisel bit to your hammer drill. Most bits slide into the front of the gun. To remove them, pull back on the collar around the bit nozzle and slide them out. Be sure to turn the gun's rotation off before using your chisel bit. Stick to wider chisels—they work better for removing thinset and help your work progress much faster. Refer to the instructions for your hammer drill—some have different routines for swapping bits and locking rotation.
Place the blade at a 45-degree angle to the thinset surface. Grip the front handle with your non-dominant hand and the back handle with your dominant hand. Pull the trigger and run the chisel along the thinset in straight vertical motions about 1 to 2 ft (0.30 to 0.61 m) in length at a time. Set your drill to the hammer setting. Avoid applying pressure to the ground unless you encounter stubborn areas. You can rent hammer drills from most home hardware shops.
Decrease the angle of your chisel blade for thicker thinset. Some guns allow you to the lock the bit at a specific angle. Make sure the rotation is off and turn the selector to the "0" setting. Decrease the angle of the chisel, and then turn the selector back to the hammer setting to lock the angle in place. For extremely stubborn areas of thinset, apply a bit of pressure as you move the tool. Avoid increasing the angle above 45 degrees—this can damage the blade.
Remove smaller patches of thinset using a chisel. Place a 1 inch (2.5 cm) putty knife at a 45-degree angle to the remaining thinset patches. Use the flat end of a 2-pound (0.91 kg) hand maul to hit the end firmly. You should notice the thinset patches breaking apart after about 20 to 30 seconds of hammering. Continue using your hammer and chisel to remove the remaining patches of thinset. Removing thinset with a hammer drill is prone to leaving small patches along your floor. If you're having trouble with patches, use a hammer and chisel or grinder to get rid of them.
Removing Thinset with an Angle Grinder
Attach a 5 to 7 in (13 to 18 cm) diamond cut wheel to your grinder. If your tool comes with a wheel outside of this size range, you need to swap it out. Remove the plate on top of the wheel by turning it counterclockwise with a wrench. Take out the second plate, also known as the cup wheel, and your blade should be easily removed. Swap in your new diamond wheel, put the cup wheel back on, and then screw the top plate back into place. A 4.5 in (11 cm) cup wheel is best for this job. If you notice your grinder has a smaller one, swap it out with one that is the proper size.
Replace your dust shroud if necessary. If your dust shroud is loose when you move it, consider installing a new one. After removing your blade and before attaching a new one, flick the dust shroud's latch and pull it outward from the grinder. Swap out the circular plastic spacer with a new one. Sand your spacer with rough 40- to 60-grit sandpaper to decrease its size. Rub the sandpaper along the outside of the spacer in a circular motion. It shouldn't take more than 5 minutes to reduce its size with rough sandpaper. After sanding, your dust shroud should fit snugly onto the spacer without jiggling.
Connect the grinder to a 5-horsepower wet-dry vacuum. The vacuum hose connects at the top of the grinder to the dust shroud. Press it into the hole in the dust shroud and it should pop in easily. After attaching it, secure the perimeter of the hose's seal with at least 1 layer of duct tape to prevent particle leakage. Always turn on your vacuum before you turn on the grinder.
Guide the 7 in (18 cm) grinder along the thinset. Turn on your grinder and grip the front handle with your non-dominant hand and the back handle with your dominant hand. Use your back hand to push the grinder forward and pull it backwards. Hold the grinder steady with your top hand to keep it from moving around. Move the grinder up and down in motions and aim to cover about 2 to 3 ft (0.61 to 0.91 m) of vertical space with each motion. Slowly move it to the right or left as you grind and don't worry about going over the same spot more than once.
Comments
0 comment